Main purposes:
To waterproof wet cement substrata before floor installation by using two-components adhesives. To consolidate dusting and incoherent concrete substrata. To prepare smooth surfaces, by sanding them, before applying cement levellers. To prepare synthetic, strong, mortars.
Technical data:
Efficiency: 200 to 300 g/m²
Dilution: alcohol 99% or our SOLVENTE H
Storage and shelf life: 6 months
Hardening: 2-3 days at 23°C (73.4°F)
Mix ratio: 1 part, in volume, of component “A”, 1 part, in volume, of component “B”
Minimum application temperature: see note ** below
Ready for traffic: 12-24 hours at 23°C (73.4°F)
Mix life: see note * below
Application: brush or squeegee
Mixing Instruction:
* the compound obtained by mixing the two components (A+B) has a service life inversely proportional to the environment temperature and to the quantity of the mix, as specified in the following table:
1 litre A+B mix - temperature: +10°C (50°F) - service life: about 1½ hours
1 litre A+B mix - temperature: +25°C (77°F) - service life: about 40 minutes
5 litres A+B mix - temperature: +10°C (50°F) - service life: about 45 minutes
5 litres A+B mix - temperature: +25°C (77°F) - service life: about 20 minutes
** Should the environment temperature be below +10°C (50°F) ACCELLERANTE HK must be added in a ratio of 2-3% of the whole amount, to avoid a too slow setting, which would compromise the final work.
Setting Instruction:
Carefully mix 1 part in volume of component A with 1 part in volume of component B and apply the so obtained compound as quick as possible. If used to waterproof: one or two coats can be applied. When laying the first coat, this must be thinned with our SOLVENTE H or with alcohol in a ratio of 20-30 parts to help penetration in the substrata. If a second coat is needed the compound must be used neat (not thinned) applying it in a layer of such a thickness as to obtain a very thin, continuous and flexible film.
If used to consolidate: Always dilute it with our SOLVENTE H or alcohol in a ratio of 40-50 parts. If used as mortar binder: Mix one part of PRIMER EP 42 with 5-6 parts of siliceous sand and, more or less, 2 parts of alcohol. This product can also be used as a binder for dusting sand on smooth surfaces, before using cement levellers, following traditional methods.
N.B. Install floors, with two-components adhesives, after 48 hours and within 7-8 days.
Cleaning:
It can be cleaned with alcohol while still wet and mechanically once dry.
Packaging:
10 litres cans component A
10 litres cans component B
Although the technical details and recommendations contained in this report correspond to the best of our knowledge and experience, all the information must in every case be taken as merely indicative and subject to confirmation after long-term practical applications. For this reason, anyone who intends to use the product must ensure beforehand that it is suitable for the envisaged applications. In any case the user only is fully responsible for any consequence deriving from the use of the product.
Technical data:
Description: pungent smelling liquid
Storage and shelf life: 12 months
Care and shelf life:
The product is easily inflammable so, please, it is very important to carefully proceed by the rules. It must be kept from hot temperature and stored in the original container far from heat sources.
Packaging:
10 litres bins
Although the technical details and recommendations contained in this report correspond to the best of our knowledge and experience, all the information must in every case be taken as merely indicative and subject to confirmation after long-term practical applications. For this reason, anyone who intends to use the product must ensure beforehand that it is suitable for the envisaged applications. In any case the user only is fully responsible for any consequence deriving from the use of the product.
Main purposes:
To consolidate dusting and incoherent, concrete or anhydrite substrata. To isolate from residual moisture wet substrata, before floorings and coatings installation. It can also be used to prepare quick setting, synthetic mortars. PRIMER PU must be used only when followed by the use of two-components adhesives.
Technical data:
Description: brown, transparent liquid
Efficiency: from 2 to 5 m²/l
Dilution: DILUENTE PU
Storage and shelf life: 12 months
Hardening: 24 hours
Application temperature: from +5°C to +25°C (41°F to 77°F)
Setting Instruction:
If used against moisture:
The substrata must be clean and enough absorbent to help the product penetration. Usually two coats of primer are applied, with an interval of 3 to 8 hours between one-another. When laying the first coat, the product must be thinned with DILUENTE PU in a ratio of 30%. When laying the second coat use it neat.
If used to consolidate:
Apply only one coat, thinned with DILUENTE PU in a ratio of 50-100% depending on the substrata absorbency. It is most important to avoid it forming a film.
If used as binder:
Mix one part of PRIMER PU with 5-6 parts of dry sand.
Surface preparation:
The product is easily inflammable so, please, it is very important to carefully proceed by the rules. It must be kept from hot temperature and stored in the original container far from heat sources.
Packaging:
10 litres bins
Although the technical details and recommendations contained in this report correspond to the best of our knowledge and experience, all the information must in every case be taken as merely indicative and subject to confirmation after long-term practical applications. For this reason, anyone who intends to use the product must ensure beforehand that it is suitable for the envisaged applications. In any case the user only is fully responsible for any consequence deriving from the use of the product.
Primer based on water to obtain a binding and firming effect on incoherent and dusting substrata when followed by the use of water based adhesives.
Main purposes:
To consolidate dusting and incoherent concrete or gypsum absorbent substrata before using water based adhesives to install wood, resilient, linoleum, cork and textile floorings. To increase cement levellers’ adhesiveness on smooth substrata. PRIMER AC is NOT suitable to be used on anhydrite substrata and with two-components adhesives.
Technical data:
Description: sky-blue, milky liquid
Application temperature: above 10°C (50°F)
Efficiency: from 100 to 300 g/m²
Waiting time: minimum 3-4 hours at 23°C (73.4°F)
Setting Instruction:
The substrata must be clean, dry and free from separating substances. If used to consolidate substrata, PRIMER AC can be used either neat or thinned with water in a ratio of 1:1 or 1:2, depending on the surface’s condition. If used as a binder for cement levellers on smooth or little absorbent substrata (possibly roughened), it has to be thinned in a ratio of 1:1 or 1:3 depending on the surface’s porosity. In both cases the product thinning has to be such as to avoid it forming a film. It can be applied with a roller or a scrubbing brush.
Surface preparation:
Substrata must be dry, clean and, as far as possible, dusted.
Care and shelf life:
It must be kept both from frost and hot temperature. It can be stored for 12 months if: in the original container, at a temperature above 5°C (41°F) and far from heat sources.
Packaging:
10 litres cans
Although the technical details and recommendations contained in this report correspond to the best of our knowledge and experience, all the information must in every case be taken as merely indicative and subject to confirmation after long-term practical applications. For this reason, anyone who intends to use the product must ensure beforehand that it is suitable for the envisaged applications. In any case the user only is fully responsible for any consequence deriving from the use of the product.
Main purposes:
It is used for fixing parquet elements which may not be perfectly anchored to the foundation. It can also be used after sandpapering and, with particular care, after polishing.
Technical data:
Description: brown, oily, viscous liquid
Application temperature: from +5°C to +40°C (41°F to 104°F)
Minimum time to calcify: 24 hours
Setting Instruction:
Make one or more holes of the diameter of 3-4 mm. on the joining point of the elements to anchor, down to the foundation. Trough this holes inject a few drops of water to moisturize the area around the little hole and than inject a few ml. af HEKOPOL P17 RIP. The quantity to be injected is related to the size of the “empty zone” underneath, keeping in mind that the product expands at least up to 3-4 its initial volume. It is possible to use it also on polished parquets, operating as above, but covering the part with adhesive tape before operating. If any smearing should occur, it can be removed with our DILUENTE PU, while still liquid. Once hardened it can only been mechanically removed.
Care and shelf life:
After use, thoroughly follow the label instructions. If stored well closed in a fresh place its shelf life is of 6 months.
Packaging:
500ml. bottles (cardboard box containing n. 15 bottles)
Although the technical details and recommendations contained in this report correspond to the best of our knowledge and experience, all the information must in every case be taken as merely indicative and subject to confirmation after long-term practical applications. For this reason, anyone who intends to use the product must ensure beforehand that it is suitable for the envisaged applications. In any case the user only is fully responsible for any consequence deriving from the use of the product.
Adhesive in watery emulsion for wood flooring. Available in both pale and dark versions.
Main purposes:
Recommended for the installation of: lamellate parquets, lamparquets, wood strips on absorbent foundations *also for those of wooden nature). Also suitable for under floor heating systems.
Technical data:
Description: beige or dark walnut dense paste
Application temperature: from +10°C to +30°C (50°F to 86°F)
Open time: max. 30 minutes (*)
Waiting time before polishing: min. 15 days (*)
Ready for traffic: min. 24 h. (*)
(*) values fixed in an environment settled at the following conditions: temperature of 23°C (73.4°F), relative humidity 50%, on concrete foundation.
N.B.: if a darker colour is needed a specific colouring paste is available.
Setting Instruction:
Wear rubber gloves and avoid skin contact during mixing, application and cleaning. Apply the adhesive only on the rough floor using a n. 4 trowel for lamellate and lamparquet type, and n. 5 trowel for listels type. Depending on the foundation surface, the needed quantity will be approximately from 600 to 800 g/m². Lay the parquet while the adhesive is wet, exerting a good pressure in order to ensure the back of the wood to get thoroughly dump. Avoid it forming a film.
Do not lay the parquet against the walls: it is very important lo leave at least 1 cm. free along the perimeter of the floor and around columns or protruding wall sections. Do not cover any expansion joint with adhesive.
Check the wood’s moisture and ascertain that it is as advised by the manufacturer (9+/-2%). Remember that too dry woods could, in time, absorb humidity from the environment and therefore swell up; whereas too wet woods could, in time, get dry and create unwonted cracking.
Surface preparation:
When laying wooden floorings it is very important to prepare the rough floor with extreme accuracy particularly for what humidity and physical state are concerned.
1) Humidity: in the whole thickness of the rough floor it must be less than 2%. Make sure that there is no possibility of humidity re-ascending from subsoil by priming (in case the work is at a ground floor). Check, as well, that the cement mix is free from hygroscopic inert substances such as pumice, clay, vermiculite which might retain water in the mixture and slowly let it out later on. If such case arouses, use only two-components adhesives.
2) Physical state:
Both new and old concrete rough floors must be clean, of compact texture and well levelled. On too absorbent substrata, or in order to consolidate loose dusting foundations, a prior treatment with PRIMER AC is needed. After our PRIMER AC has been applied, any unevenness should be removed using our HEKOPLANER AR SPECIAL, which has a high grade of mechanical resistance. Please remember that if the leveller are not perfectly fixed, unwanted disjunction may occur. Each case should be evaluated separately.
Cleaning:
Parquet, tools and clothes can be cleaned with water while the adhesive is still fresh. Once hardened it can been removed with alcohol.
Care and shelf life:
It must be kept both from frost and hot temperature. Its shelf life is of al least 12 months if stored in the original container at a temperature above 5°C (41°F) and far from heat sources.
Packaging:
22 Kg. bins
Although the technical details and recommendations contained in this report correspond to the best of our knowledge and experience, all the information must in every case be taken as merely indicative and subject to confirmation after long-term practical applications. For this reason, anyone who intends to use the product must ensure beforehand that it is suitable for the envisaged applications. In any case the user only is fully responsible for any consequence deriving from the use of the product.
Quick setting and highly efficient adhesive for wood flooring, based on co-polymers in watery emulsion.
Main purposes:
Recommended for the installation of: lamellate parquets, lamparquets, wood strips on absorbent foundations (also for those of wooden nature). It is possible to utilize it on pre-finished multi-strata parquets. Also suitable for under floor heating systems. Thanks to the fact that it contents very little water, the use of this product consents to reduce wood deformations and allows minimum wait before polishing.
Technical data:
Description: whitish dense paste
Dry Film peculiarity: elastic, semi-transparent
Application temperature: from +10°C to +30°C (50°F to 86°F)
Open time: max. 15 minutes (*)
Waiting time before polishing: min. 4 days (*)
5DD Ready for traffic: min. 12 h. (*
(*) values fixed in an environment settled at the following conditions: temperature of 23°C (73.4°F), relative humidity 50%, on concrete foundation.
Setting Instruction:
Wear rubber gloves and avoid skin contact during mixing, application and cleaning. Apply the adhesive only on the rough floor using a n. 4 trowel for lamellate and lamparquet type, and n. 5 trowel for listels type. Depending on the foundation surface, the needed quantity will be approximately from 400 to 700 g/square meter. Lay the flooring while the adhesive is wet, exerting a good pressure in order to ensure the back of the wood to get thoroughly dump. Avoid it forming a film.
Please, remember that, on traditional parquets, possible adhesive smudges can swell if they get in contact with solvent varnishes. Do not lay the parquet against the walls: it is very important lo leave at least 1 cm. free along th 5B4 e perimeter of the floor and around columns or protruding wall sections. Do not cover any expansion joint with adhesive. Check the wood’s moisture and ascertain that it is as advised by the manufacturer (9+/-2%).
Remember that too dry woods could, in time, absorb humidity from the environment and therefore swell up, whereas too wet woods could, in time, get dry and create unwonted cracking.
Surface preparation:
When laying wooden floorings it is very important to prepare the rough floor with extreme accuracy particularly for what humidity and physical state are concerned.
1) Humidity: in the whole thickness of the rough floor it must be less than 2% . If an under floor heating system is installed it must be less than 1.7%. Make sure that there is no possibility of humidity re-ascending from subsoil by priming (in case the work is at a ground floor). Check, as well, that the cement mix is free from hygroscopic inert substances such as pumice, clay, vermiculite which might retain water in the mixture and slowly let it out later on. If such case arouses, use only bi-component adhesives.
2) Physical state:
Both new and old concrete rough floors must be clean, of compact texture and well levelled. On too absorbent substrata, or 7E5 in order to consolidate loose dusting foundations, a prior treatment with PRIMER AC is needed. After our PRIMER AC has been applied, any unevenness should be removed using our HEKOPLANER AR SPECIAL, which has a high grade of mechanical resistance. Please remember that if the leveller are not perfectly fixed, unwanted disjunction may occur. Each case should be evaluated separately.
Cleaning:
Parquet, tools and clothes can be cleaned with water while the adhesive is still fresh. Once hardened it can been removed with alcohol.
Care and shelf life:
It must be kept from both frost and hot temperature. Its shelf life is of al least 12 months if stored in the original container at a temperature above 5°C (41°F) and far from heat sources.
Packaging:
20 Kg. bins
Although the technical details and recommendations contained in this report correspond to the best of our knowledge and experience, all the information must in every case be taken as merely indicative and subject to confirmation after long-term practical applications. For this reason, anyone who intends to use the product must ensure beforehand that it is suitable for the envisaged applications. In any case the user only is fully responsible for any consequence deriving from the use of the product.
A two-components epoxy-poliyurethanic adhesive, for wood floor covering, very little irritating. Available in both dark and light version.
Main purposes:
Recommended for the installation of any type of wood floor covering on: cement, anhydrite, marble tile, tiled floors, stone materials, wood panels and metal sheets foundations.
Technical data:
Description: A component: a white dense paste, B component: thixotropic beige or brown liquid
Application temperature: from +10°C to +30°C (50°F to 86°F)
Waiting time before polishing: 3 days at +15° C (59° F), 2 days at +25° C (77° F)
Ready for traffic: 24 h. at +15° C (59° F), 12 h. at +25° C (77° F)
Mixture utilization time: A+B (9 Kg. + 1 Kg.):
2 h. at +15° C (59° F)
1 h. at +25° C (77° F)
Also suitable for heated systems floors.
Setting Instruction:
Wear rubber gloves and avoid skin contact during mixing, application and cleaning. Pour all the content of component B into the component A container and mix thoroughly to achieve a smooth homogeneous paste consistency (pale colour = oak /dark colour = walnut). Note that the two components (A and B) are packaged to the exact ratio. It is very important to mix one bin of component A and one bin of component B at time. Apply the adhesive only on the rough floor using a n. 5 trowel for any kind of parquet. Depending on the foundation surface, the needed quantity will be approximately from 800 to 1200 gr./m². Lay the flooring while the adhesive is wet, exerting a good pressure in order to ensure the back of the wood to get thoroughly dump.
Do not lay the parquet against the walls: it is very important lo leave at least 1 cm. free along the perimeter of the floor and around columns or protruding wall sections. Do not cover any expansion joint with adhesive.
Surface preparation:
When laying wooden floorings it is very important to prepare the rough floor with extreme accuracy particularly for what humidity and physical state are concerned.
1) Humidity: in the whole thickness of the rough floor it must not exceed 2% for concrete or stone material foundations and 0.5% for anhydrite foundations. Arrange in the foundations a steam stop to avoid humidity re-ascending from subsoil by priming. Check that the cement mix is free from hygroscopic inert substances, such as pumice, clay, vermiculite, which might retain water in the mixture and slowly let it out later on. Use our PRIMER PU only to stop modest quantities of residual humidity in absorbent foundations. When dealing with non-absorbent foundations the usage of our PRIMER EP42 (two-component) is suggested.
2) Physical state:
a) Both new and old concrete rough floors must be clean, of compact texture and well levelled. PRIMER PU, besides being used against humidity, can also been useful to consolidate loose dusting foundations. After our PRIMER AC has been applied, any unevenness should be removed using our HEKOPLANER AR SPECIAL, which has a high grade of mechanical resistance. Please remember that if the leveller are not perfectly fixed, unwanted disjunction may occur (see the note about 88F the leveller use).
b) Anhydrite foundations must be roughened with sandpaper (grain 16), thoroughly dusted, and spread with PRIMER PU diluted with DILUENTE PU. It is important to avoid it forming a film.
c) Marble tile, varnished tile floors, stone materials foundations should be slightly roughened. If this should not be possible they must be cleaned with a caustic soda solution (in a 10% ratio), thoroughly rinsed and, when dry, spread with our PRIMER PRA.
d) Bisque foundation (not varnished tile floors) must be previously consolidated with PRIMER PU diluted in a ratio of a 1 to 1 with the right thinner.
Cleaning:
Parquet, tools and clothes can be cleaned with alcohol while the adhesive is still fresh. Once hardened it can only been mechanically removed.
Care and shelf life:
12 months if stored in the original container and far from heat sources.
Packaging:
4.5 Kg. + 0.5 Kg. bins
9 Kg. + 1 Kg. bins
Although the technical details and recommendations contained in this report correspond to the best of our knowledge and experience, all the information must in every case be taken as merely indicative and subject to confirmation after long-term practical applications. For this reason, anyone who intends to use the product must ensure beforehand that it is suitable for the envisaged applications. In any case the user only is fully responsible for any consequence deriving from the use of the product.
A two-components epoxy-poliyurethanic adhesive for wood floor covering
Main purposes:
Recommended for the installation of any type of wood floor covering on: cement, anhydrite, marble tile, tiled floors, stone materials, wood panels and metal sheets foundations.
Technical data:
Description: A component: a white dense paste, B component: thixotropic beige or brown liquid
Application temperature: from +10°C to +30°C (50°F to 86°F)
Waiting time before polishing: 3 days at +15° C (59° F), 2 days at +25° C (77° F)
Ready for traffic: 24 h. at +15° C (59° F), 12 h. at +25° C (77° F)
Mixture utilization time: A+B (9 Kg. + 1 Kg.):
2 h. at +15° C (59° F)
1 h. at +25° C (77° F)
5CA Also suitable for under floor heating sistems.
Setting Instruction:
Wear rubber gloves and avoid skin contact during mixing, application and cleaning. Pour all the content of component B into the component A container and mix thoroughly to achieve a smooth homogeneous paste consistency (pale colour = oak /dark colour = walnut). Note that the two components (A and B) are packaged to the exact ratio. It is very important to mix one bin of component A and one bin of component B at time. Apply the adhesive only on the rough floor using a n. 2 trowel for lamellar and lamparquet type, and n. 4 trowel for listels type. Depending on the foundation surface, the needed quantity will be approximately from 800 to 1200 g/square meter. Lay the flooring while the adhesive is wet, exerting a good pressure in order to ensure the back of the wood to get thoroughly dump. Do not lay the parquet against the walls: it is very important lo leave at least 1 cm. free along the perimeter of the floor and around columns or protruding wall sections.
Do not cover any expansion joint with adhesive.
Surface preparation:
When laying wooden floorings it is very important to prepare the rough floor with extreme accuracy particularly for what humidity and physical state are concerned.
1) Humidity: in the whole thickness of the rough floor it must not exceed 2% for concrete or stone material foundations and 0.5% for anhydrite foundations. Arrange in the foundations a steam stop to avoid humidity re-ascending from subsoil by priming. Check that the cement mix is free from hygroscopic inert substances such as pumice, clay, vermiculite which might retain water in the mixture and slowly let it out later on. Use our PRIMER PU only to stop modest quantities of residual humidity in absorbent foundations. When dealing with non-absorbent foundations the usage of our PRIMER EP3 (three-component) is suggested.
2) Physical state:
a) Both new and old concrete rough floors must be clean, of compact texture and well levelled. PRIMER PU, besides being used against humidity, can also been useful to consolidate loose dusting foundations. After our PRIMER AC has been applied, any unevenness should be removed using our HEKOPLANER AR SPECIAL, which has a high grade of mechanical resistance. Please remember that if the leveller are not perfectly fixed, unwanted disjunction may occur (see the note about the leveller use).
b) Anhydrite foundations must be roughened with sandpaper (grain 16), thoroughly dusted, and spread with PRIMER PU diluted with DILUENTE PU. It is important to avoid it forming a film.
c) Marble tile, varnished tile floors, stone materials foundations should be slightly roughened. If this should not be possible they must be cleaned with a caustic soda solution (in a 10% ratio), thoroughly rinsed and, when dry, spread with our PRIMER PRA.
d) Bisque foundation (not varnished tile floors) must be previously consolidated with PRIMER PU diluted in a ratio of a 1 to 1 with the right thinner.
Cleaning:
Parquet, tools and clothes can be cleaned with alcohol while the adhesive is still fresh. Once hardened it can only been mechanically removed.
Care and shelf life:
12 months if stored in the original container and far from heat sources
Packaging:
Bin: 4.5 Kg. + 0.5 Kg.
9 Kg. + 1 Kg.
Although the technical details and recommendations contained in this report correspond to the best of our knowledge and experience, all the information must in every case be taken as merely indicative and subject to confirmation after long-term practical applications. For this reason, anyone who intends to use the product must ensure beforehand that it is suitable for the envisaged applications. In any case the user only is fully responsible for any consequence deriving from the use of the product.