Quick setting and highly efficient adhesive for wood flooring, based on co-polymers in watery emulsion.
Main purposes:
Recommended for the installation of: lamellate parquets, lamparquets, wood strips on absorbent foundations (also for those of wooden nature). It is possible to utilize it on pre-finished multi-strata parquets. Also suitable for under floor heating systems. Thanks to the fact that it contents very little water, the use of this product consents to reduce wood deformations and allows minimum wait before polishing.
Technical data:
Description: whitish dense paste
Dry Film peculiarity: elastic, semi-transparent
Application temperature: from +10°C to +30°C (50°F to 86°F)
Open time: max. 15 minutes (*)
Waiting time before polishing: min. 4 days (*)
5DD Ready for traffic: min. 12 h. (*
(*) values fixed in an environment settled at the following conditions: temperature of 23°C (73.4°F), relative humidity 50%, on concrete foundation.
Setting Instruction:
Wear rubber gloves and avoid skin contact during mixing, application and cleaning. Apply the adhesive only on the rough floor using a n. 4 trowel for lamellate and lamparquet type, and n. 5 trowel for listels type. Depending on the foundation surface, the needed quantity will be approximately from 400 to 700 g/square meter. Lay the flooring while the adhesive is wet, exerting a good pressure in order to ensure the back of the wood to get thoroughly dump. Avoid it forming a film.
Please, remember that, on traditional parquets, possible adhesive smudges can swell if they get in contact with solvent varnishes. Do not lay the parquet against the walls: it is very important lo leave at least 1 cm. free along th 5B4 e perimeter of the floor and around columns or protruding wall sections. Do not cover any expansion joint with adhesive. Check the wood’s moisture and ascertain that it is as advised by the manufacturer (9+/-2%).
Remember that too dry woods could, in time, absorb humidity from the environment and therefore swell up, whereas too wet woods could, in time, get dry and create unwonted cracking.
Surface preparation:
When laying wooden floorings it is very important to prepare the rough floor with extreme accuracy particularly for what humidity and physical state are concerned.
1) Humidity: in the whole thickness of the rough floor it must be less than 2% . If an under floor heating system is installed it must be less than 1.7%. Make sure that there is no possibility of humidity re-ascending from subsoil by priming (in case the work is at a ground floor). Check, as well, that the cement mix is free from hygroscopic inert substances such as pumice, clay, vermiculite which might retain water in the mixture and slowly let it out later on. If such case arouses, use only bi-component adhesives.
2) Physical state:
Both new and old concrete rough floors must be clean, of compact texture and well levelled. On too absorbent substrata, or 7E5 in order to consolidate loose dusting foundations, a prior treatment with PRIMER AC is needed. After our PRIMER AC has been applied, any unevenness should be removed using our HEKOPLANER AR SPECIAL, which has a high grade of mechanical resistance. Please remember that if the leveller are not perfectly fixed, unwanted disjunction may occur. Each case should be evaluated separately.
Cleaning:
Parquet, tools and clothes can be cleaned with water while the adhesive is still fresh. Once hardened it can been removed with alcohol.
Care and shelf life:
It must be kept from both frost and hot temperature. Its shelf life is of al least 12 months if stored in the original container at a temperature above 5°C (41°F) and far from heat sources.
Packaging:
20 Kg. bins
Although the technical details and recommendations contained in this report correspond to the best of our knowledge and experience, all the information must in every case be taken as merely indicative and subject to confirmation after long-term practical applications. For this reason, anyone who intends to use the product must ensure beforehand that it is suitable for the envisaged applications. In any case the user only is fully responsible for any consequence deriving from the use of the product.